Solar · Storage · Off-grid B2B worldwide export wholesaler

Professional equipment supply for installers, EPC contractors and distributors.


Grundfos borehole motors and accessories

SINES - Grundfos - MS and MMS submersible motors

Official Grundfos distributor, SINES Export supplies everything that goes around an SP submersible pump: MS 402, MS 4000 and MS 6000 motors, MMS rewindable motors, MP 204 electronic protection, motor cables and submersible cables, cable joint kits, non-return valves, strainers and cooling sleeves. Everything needed to equip a new borehole, but above all to put back into service a pump whose motor, cable or joint has failed, without buying the complete set again.

A submersible motor rarely burns out without a reason: insulation fault at the joint, insufficient cooling, dry running or too-frequent starts. Each product page sets out the rules of the Grundfos data booklet, and the guide below brings together the essentials: choosing the motor, cooling it, sizing the cable and protecting it.

For a replacement, send us the pump and motor nameplates, the installation depth and the available voltage: we prepare the complete motor, cable, joint and protection set, for worldwide export. In solar pumping, the RSI inverter has its own built-in protections.


GRUNDFOS 4" MS 402 / MS 4000 MOTORS
4" submersible motors

Single-phase MS 402 from 0.37 to 1.5 kW and three-phase MS 4000 up to 7.5 kW, for 4" SP pumps: replacement and repair.


On request
GRUNDFOS 6" MS 6000 MOTORS
6" three-phase submersible motors

From 5.5 to 30 kW at 3 × 400 V, direct-on-line or star-delta start, for medium- and high-flow SP pumps.


On request
GRUNDFOS MMS MOTORS
Rewindable submersible motors

MMS 6, MMS 8000 and MMS 10000 from 22 to 147 kW: repairable by rewinding, for large water supply boreholes.


On request
GRUNDFOS MP 204
Electronic motor protection

Insulation before start, temperature, overload and dry running; PR 5714 relay and Pt100 / Pt1000 sensors.


On request
GRUNDFOS CABLES AND JOINTS
Motor cables, submersible cables, joints

MS motor cables with plug, 4G1.5 submersible cables, KM heat-shrink cable joint kits and cable clips.


On request
GRUNDFOS BOREHOLE ACCESSORIES
Non-return valves, strainers, sleeves

Non-return valves, stainless-steel suction strainers and cooling sleeve supports for SP pumps.


On request

Which Grundfos motor or accessory should you choose?


Range Diameter Power range Power supply Used for
MS 4024"0.37 to 1.5 kW1 × 230 V4" SP pumps in single-phase, sites without a three-phase supply
MS 40004"2.2 to 7.5 kW3 × 400 V4" SP pumps in three-phase, solar pumping with RSI
MS 60006"5.5 to 30 kW3 × 400 V6" SP pumps (SP 17 to SP 95 depending on power), water supply and irrigation
MMS6", 8", 10"22 to 147 kW3 × 400 VLarge boreholes, motors repairable by rewinding
MP 204control box3 to 999 A100 to 480 VMotor protection on mains or generator supply
Cables and joints4" and 6"1.5 to 10 mm²depending on motorMotor cable replacement, extension, watertight joint

The motor is chosen according to the pump: diameter, power stated on the SP pump nameplate and voltage available on site. The cable is then sized according to the length between the control box and the pump, and the protection according to the rated motor current. For a replacement, a motor identical to the original avoids any modification to the riser pipe and the control box.

In solar pumping, the RSI inverter controls the MS 4000 and MS 6000 motors and has its own built-in protections (overvoltage, overload, overtemperature), with a dry-running sensor as an accessory. The MP 204 is worthwhile on installations powered by the mains or a generator.

Equipping an SP borehole: motor, cable, protection


A submersible pump almost never fails by itself: motors burn out through insulation faults, overheating or dry running, and all three causes are dealt with at installation. Here are the rules from the Grundfos data booklet that we apply to every borehole.

Choosing the motor
The motor is chosen with the pump: its power P2 must cover the duty point, and its diameter must fit the borehole. 4" MS 402 and MS 4000 up to 7.5 kW, 6" MS 6000 from 5.5 to 30 kW, rewindable MMS from 22 to 147 kW in the Grundfos catalogue. The MMS is repaired by rewinding, an asset on sites far from Grundfos workshops.

Cooling the motor
Water must flow along the motor at no less than 0.15 m/s for water up to 40 °C. Place the motor above the borehole screens; if the borehole is much wider than the pump, if the pump is below the screens or installed horizontally, add a cooling sleeve.

Sizing the cable
The voltage drop in the submersible cable must not exceed 3 %; the table below gives the maximum length between control box and pump for direct-on-line starting at 3 × 400 V. With star-delta starting, the length can be multiplied by 1.73. A larger cross-section reduces losses: on a borehole that runs all year round, it quickly pays for itself.

Protecting
An MP 204 protection unit measures the insulation before each start, monitors the temperature via the Tempcon sensor and stops the pump in the event of underload, a sign of dry running. Add a surge arrester, respect the motor's number of starts per hour and measure the insulation at every service visit: below 0.5 MΩ, action is needed.

Maximum submersible cable length, in metres from the control box to the pump
3 × 400 V, 50 Hz, direct-on-line start, voltage drop 3 %, water at 30 °C (Grundfos SP data booklet). For star-delta, multiply by 1.73.

Motor kW In (A) 1.5 mm² 2.5 mm² 4 mm² 6 mm² 10 mm² 16 mm² 25 mm² 35 mm²
4"0.371.4462767––––––
4"0.552.2294488777–––––
4"0.752.3250416662987––––
4"1.13.4169281448668––––
4"1.54.2132219348520857–––
4"2.25.592153244364602951––
4"37.8569114182271447705––
4"49.65490143214353557853–
4"5.5133966104156258407624855
4"7.518.8284775112185291445609
6"5.513.64066105157258407622850
6"7.517.6294978117193304465637
6"9.221.823396293154243372510
6"1124.8–345380132209320440
6"1330–284568112176270370
6"1534––395997154236324
6"18.542–––4880126193265
6"2248–––4167107164225
6"2657––––5790138189
6"3066.5––––4978119164
Max. cable current23 A30 A41 A53 A74 A99 A131 A162 A

Frequently asked questions


Can the motor of an SP pump be replaced on its own?
Yes. If the pump end is in good condition, the motor is replaced by an MS or MMS of the same power and diameter, with a new motor cable. We check the compatibility between pump and motor with you from the nameplate.

Which cable cross-section for my borehole?
It depends on the power, the current and the length between the control box and the pump. The table above gives the maximum lengths for a 3 % voltage drop with direct-on-line starting at 3 × 400 V; send us these three figures and we will do the calculation.

Why a rewindable motor?
An MMS whose winding has burnt out can be rewound in a specialist workshop instead of being replaced. For high power ratings and remote sites, this reduces the cost and the time needed to return to service.

Is the MP 204 useful with an RSI solar inverter?
No: the MP 204 is not used downstream of a frequency converter or an inverter. The RSI has its own built-in protections (overload, underload, overvoltage). The MP 204 is used on pumps powered by the mains or a generator.

Size your solar pumping system in two minutes

LE LAB, our free online tool, sizes it from your water need, the depth and your location: recommended pump, controller and PV power. No account required.

Launch LE LAB Or request a free study
Project support · Worldwide delivery

Get the support your project needs

From product selection to export logistics, our team helps installers, EPCs and distributors turn a requirement into a clear professional quotation.

B2B supply Sea or air freight Worldwide export
From requirement to delivery
  1. 01Share your products and quantities
  2. 02Receive a clear B2B quotation
  3. 03We coordinate worldwide delivery
Start your request