Solar · Storage · Off-grid B2B worldwide export wholesaler

Professional equipment supply for installers, EPC contractors and distributors.

SINES - Grundfos borehole accessories


GRUNDFOS BOREHOLE HYDRAULIC ACCESSORIES



The hydraulic accessories that protect the submersible pump: non-return valves, suction strainers and cooling sleeves

Around the pump and the motor, three accessories prevent most failures: the non-return valve, which keeps the riser pipe full and protects against water hammer; the strainer, which stops debris entering the pump inlet when the pump works in a basin, an open well or a tank; the cooling sleeve, which forces the water to flow along the motor when the borehole is too wide, or when the pump is below the borehole screens or installed horizontally. Grundfos supplies stainless-steel strainers with clamp in nine sizes and sets of sleeve supports for SP pumps.


Non-return valves

PVC, composite or cast iron
1 1/4" to DN 80

Strainers

perforated stainless steel with clamp
D115 to D330

Sleeves

supports for SP flow sleeve
145 x 450 to 250 x 1000

Worldwide B2B pump supply and export

SP pumps have a built-in non-return valve. An additional valve is fitted on the discharge pipe at the surface or on long riser pipes to isolate the pipework, limit water hammer and make maintenance easier: PVC female-female valves 1 1/2" and 2", composite valve and PN 10 valve in 1 1/4", flanged valve DN 80 PN 10 for higher flow rates.

The cooling sleeve (flow sleeve) is a tube that surrounds the pump and the motor so that the water drawn in flows along the motor at a velocity of 0.5 to 3 m/s. Grundfos recommends it when the motor is subject to a high thermal load (current unbalance, dry running, overload, hot water), in aggressive water (corrosion doubles with every 10 °C rise), where deposits form on the motor, and when the pump is installed horizontally or below the borehole screens. The velocity is calculated as V = Q × 353 / (D² - d²), with Q in m³/h, D the inside diameter of the sleeve and d that of the motor in mm. The SP flow sleeve support sets (centring feet and clamps) fix the sleeve around the pump, from size 145 x 450 to size 250 x 1000 according to the Grundfos designation.

The perforated stainless-steel strainers, supplied with their clamp, protect the inlet of a submersible pump installed in a basin, a tank, an open well or a watercourse, where leaves, coarse sand and debris may be drawn in. Nine sizes are available, from D115 to D330 according to the Grundfos designation; we tell you which one suits your pump.

Applications: submersible pumps in wide boreholes or open wells, installations in basins, tanks or watercourses, horizontally installed pumps, hot or aggressive water, protection of pipework against water hammer.

Official Grundfos distributor, SINES Export supplies Grundfos motors, protection units, cables and borehole accessories to installers, drillers, operators and NGOs, for worldwide export. For a replacement, send us the pump and motor nameplates: we check compatibility and prepare the complete motor, cable, joint and protection set. See also the SP submersible pumps, the RSI solar inverter and the “equipping an SP borehole” guide.

Cooling sleeve

Parameter Value
Flow velocity along the motor0.5 to 3 m/s (motor minimum: 0.15 m/s up to 40 °C)
CalculationV = Q × 353 / (D² - d²), Q in m³/h, D and d in mm
Essential ifborehole much wider than the motor, pump below the screens, horizontal installation, hot or aggressive water, deposits
Supports in the catalogueSP flow sleeve 145 x 450, 180 x 1000, 200 x 800, 210 x 1000, 250 x 1000 (Grundfos designation)

Data from the Grundfos SP A, SP data booklet (50 Hz). Full data, versions and other voltages on the Grundfos Product Center or on request.

Official Grundfos documents.

Need sizing or a replacement? Contact us with the nameplate: we prepare the complete set.

References & article codes


Grundfos catalogue codes. Complete sleeves, zinc anodes for brackish water and SP thread-to-flange connecting pieces on request.

Non-return valves

Article code Grundfos designation
96003826Non-return valve DN80 PN10
96005308Composite non-return valve 1"1/4
96023843Non-return valve 1"1/2 F/F PVC
96023844Non-return valve 2" F/F PVC
96116550Non-return valve DN11/4" PN10

Stainless-steel suction strainers

Article code Grundfos designation
97942211Strainer D115 x 117 x 1.0
97942214Strainer D145 x 158 x 1.0
97942218Strainer D180 x 192 x 1.0
97942230Strainer D160 x 158 x 1.0
97942247Strainer D200 x 190 x 1.0
97942261Strainer D210 x 192 x 1.0
97942263Strainer D254 x 325 x 1.0
97942268Strainer D330 x 385 x 1.0
97942269Strainer D285 x 385 x 1.0

SP cooling sleeve supports

Article code Grundfos designation
96957523SUPPORT FOR COOLING SLEEVE SP 145 x 450
96957529SUPPORT FOR COOLING SLEEVE SP 180 x 1000
96957545SUPPORT FOR COOLING SLEEVE SP 200 x 800
96957546SUPPORT FOR COOLING SLEEVE SP 210 x 1000
96957548SUPPORT FOR COOLING SLEEVE SP 250 x 1000

Size your solar pumping system in two minutes

LE LAB, our free online tool, sizes it from your water need, the depth and your location: recommended pump, controller and PV power. No account required.

Launch LE LAB Or request a free study
Project support · Worldwide delivery

Get the support your project needs

From product selection to export logistics, our team helps installers, EPCs and distributors turn a requirement into a clear professional quotation.

B2B supply Sea or air freight Worldwide export
From requirement to delivery
  1. 01Share your products and quantities
  2. 02Receive a clear B2B quotation
  3. 03We coordinate worldwide delivery
Start your request