Solar · Storage · Off-grid B2B worldwide export wholesaler

Professional equipment supply for installers, EPC contractors and distributors.

SINES - Grundfos MS 402 and MS 4000


GRUNDFOS 4" MS 402 AND MS 4000 MOTORS



4" stainless-steel submersible motors: single-phase MS 402 from 0.37 to 1.5 kW and three-phase MS 4000 from 2.2 to 7.5 kW, to equip or recommission a 4" SP pump

The MS 402 and MS 4000 motors drive Grundfos 4" submersible pumps (SP 1A to SP 5A, SP 7 to SP 17 depending on power). Stainless-steel sleeve, shaft and end shields, encapsulated stator embedded in resin, cooling by internal recirculation of the motor liquid: they can be replaced on their own when the pump is sound, which avoids buying the complete set again after a failure in the borehole. The MS 4000 is available in an R version (904L stainless steel, SiC/SiC shaft seal) for aggressive water and can be fitted with a Tempcon temperature sensor read by the MP 204.


MS 402

single-phase 1 × 220-230 V
0.37 to 1.5 kW

MS 4000

three-phase 3 × 380-415 V
2.2 to 7.5 kW

Ø 95 mm

stainless steel
15 bar (MS 402) / 60 bar (MS 4000)

Worldwide B2B pump supply and export

The MS 402 covers the low power ratings, from 0.37 to 2.2 kW, in single-phase 2-wire or 3-wire or in three-phase; the single-phase 2-wire MS 402 has built-in motor protection and connects directly to the mains, while the 3-wire version connects via a starter box. Its shaft seal is a rubber lip seal approved for drinking water, with a ceramic radial bearing and a ceramic-carbon thrust bearing. The MS 4000, three-phase from 0.75 to 7.5 kW, has a spring-loaded ceramic/tungsten carbide mechanical shaft seal with sand shield, or SiC/SiC in the R version; it withstands 100 starts per hour and 300 per day, and is available in a T60 industrial version for liquid up to 60 °C.

All MS motors are factory-filled with a motor liquid based on monopropylene glycol, non-toxic and frost-proof down to -20 °C. Before installation, after long storage or transport, the level is checked and topped up with demineralised water or clean tap water through the filling hole (at the bottom of the MS 402, on the end shield of the MS 4000), with the motor tilted, turning the shaft to expel the air. The insulation resistance is measured before the cable is connected, after the joint is made and once the motor is in the borehole: below 0.5 MΩ, the motor, the cable or the joint must be repaired.

Cooling depends on the water velocity along the motor: at least 0.15 m/s for liquid up to 40 °C. In a borehole much wider than the pump, or when the pump is placed below the borehole screens or horizontally, a cooling sleeve is required. The motor operates permanently submerged, with the pump inlet always under water.

Applications: replacing the motor of a failed 4" SP pump, fitting a new SP pump end to an existing motor, changing from single-phase to three-phase, repairing domestic, agricultural and village boreholes.

Official Grundfos distributor, SINES Export supplies Grundfos motors, protection units, cables and borehole accessories to installers, drillers, operators and NGOs, for worldwide export. For a replacement, send us the pump and motor nameplates: we check compatibility and prepare the complete motor, cable, joint and protection set. See also the SP submersible pumps, the RSI solar inverter and the “equipping an SP borehole” guide.

MS 402 single-phase 1 × 230 V, 50 Hz

Power P2 Current In Efficiency at 100 % Cos φ at 100 % Ist / In Length Weight
0.37 kW3.95 A57 %0.773.4256 mm6.8 kg
0.55 kW5.8 A59.5 %0.743.5291 mm8.2 kg
0.75 kW7.45 A60 %0.793.6306 mm8.9 kg
1.1 kW7.3 A72.5 %0.994.3346 mm10.5 kg
1.5 kW10.2 A71 %0.983.9346 mm11 kg

MS 4000 three-phase 3 × 400 V, 50 Hz

Power P2 Current In Efficiency at 100 % Cos φ at 100 % Ist / In Length Weight
2.2 kW6.05 A74.5 %0.744.5456 mm16 kg
3 kW7.85 A75.2 %0.774.5496 mm17 kg
4 kW9.6 A78 %0.84.8576 mm21 kg
5.5 kW13 A79.8 %0.814.9676 mm26 kg
7.5 kW18.8 A78.2 %0.784.5776 mm31 kg

Common specifications

Specification Value
Diameter95 mm (4")
Materialsstainless-steel sleeve, end shields and shaft; R version of the MS 4000 in EN 1.4539 (904L), shaft EN 1.4462
Shaft sealMS 402: NBR lip seal; MS 4000: ceramic / tungsten carbide, SiC/SiC in the R version
Max. operating pressureMS 402: 15 bar; MS 4000: 60 bar
Max. liquid temperature40 °C at 0.15 m/s along the motor (60 °C in T60 version)
Starts100 per hour and 300 per day maximum, at least 1 per year
Motor liquidSML-3 with propylene glycol, frost-proof down to -20 °C
Temperature sensorTempcon optional on MS 4000 (read by MP 204), Pt1000 with fixing kit

Data from the Grundfos SP A, SP data booklet (50 Hz). Full data, versions and other voltages on the Grundfos Product Center or on request.

Official Grundfos documents.

Need sizing or a replacement? Contact us with the nameplate: we prepare the complete set.

References & article codes


Grundfos catalogue codes, motors supplied without cable: order the appropriate motor cable with plug, see the cables and joints product page. Other power ratings, voltages and R or T60 versions on request.

MS 402 single-phase

Article code Grundfos designation Power Power supply
96766074MS402 1X220V/50 0.37kW without cable emb0.37 kW1 × 220-230 V, 50 Hz
96766075MS402 1X220V/50 0.55kW without cable emb0.55 kW1 × 220-230 V, 50 Hz
96766077MS402 1X220V/50 0.75kW without cable emb0.75 kW1 × 220-230 V, 50 Hz
96591067MS402 1X220V/50 1.10kW without cable1.1 kW1 × 220-230 V, 50 Hz
96765992MS402 1X230V/50 1.50kW without cable emb1.5 kW1 × 220-230 V, 50 Hz

MS 4000 three-phase

Article code Grundfos designation Power Power supply
7C192708MS4000ARBSWLMXT4 3x380-415/50 3.00kW3 kW3 × 380-415 V, 50 Hz
7C192510MS4000AZBCWLMXT4 3x380-415/50 4.00kW4 kW3 × 380-415 V, 50 Hz
7C193711MS4000ARBSWLMJT4 3x380-415/50 5.50kW5.5 kW3 × 380-415 V, 50 Hz
7C193911MS4000ARESWLMJT4 3x380-415/50 5.50kW5.5 kW3 × 380-415 V, 50 Hz
7C192511MS4000AZBCWLMXT4 3x380-415/50 5.50kW5.5 kW3 × 380-415 V, 50 Hz
7C193311MS4000AZBSWLMJT4 3x380-415/50 5.50kW5.5 kW3 × 380-415 V, 50 Hz
7C193512MS4000AZBCWLMJT4 3x380-415/50 7.50kW7.5 kW3 × 380-415 V, 50 Hz

Size your solar pumping system in two minutes

LE LAB, our free online tool, sizes it from your water need, the depth and your location: recommended pump, controller and PV power. No account required.

Launch LE LAB Or request a free study
Project support · Worldwide delivery

Get the support your project needs

From product selection to export logistics, our team helps installers, EPCs and distributors turn a requirement into a clear professional quotation.

B2B supply Sea or air freight Worldwide export
From requirement to delivery
  1. 01Share your products and quantities
  2. 02Receive a clear B2B quotation
  3. 03We coordinate worldwide delivery
Start your request