Solar · Storage · Off-grid B2B worldwide export wholesaler

Professional equipment supply for installers, EPC contractors and distributors.

SINES - Grundfos CUE for SP and SPE submersible pumps


GRUNDFOS CUE FOR SP AND SPE PUMPS



The Grundfos rules for controlling an SP or SPE submersible pump with a CUE frequency converter, and the official motor, CUE and filter selection table

An SPE pump only works with a frequency converter, and an SP pump gains variable speed with a CUE. Grundfos then requires a sine-wave filter, for the SP as soon as its motor is supplied at 380 V and above, and precise cabling rules.


Sine-wave filter

mandatory
SP 380 V and above, SPE

Current

selection criterion
for the CUE size

300 m

max. motor cable
with sine-wave filter

Worldwide B2B pump supply and export

SP pumps: with a submersible motor supplied at 380 V and above, the CUE manual requires a sine-wave filter, whatever the power, for a motor cable of up to 300 m. The CUE and the filter are installed near the borehole, or further away with a screened cable running to a terminal box placed near the borehole.

SPE pumps: their MS6000P permanent-magnet motor requires a frequency converter. Grundfos offers the CUE for this purpose and recommends the RSI inverter for solar applications. The sine-wave filter is mandatory and is selected on the motor current at 100 Hz; the CUE is sized on the current, never on the power alone.

Grundfos settings for SPE pumps: ramp-up and ramp-down times of 3 seconds maximum, continuous operation at 55 Hz minimum to lubricate the bearings, voltage peaks limited to 800 V and never exceeding 850 V at the motor terminals, and dU/dt limited to 1 000 V/µs, hence the filter at the CUE output.

Motor protection: with a CUE, no additional overload protection is needed. Tempcon sensors do not work with a frequency converter; the motor temperature is monitored by a Pt100 or Pt1000 sensor connected to the MCB 114 module. The drop cable remains unscreened; screened cables are used on sites sensitive to electromagnetic interference.

Useful functions in boreholes: constant pressure, constant level, constant flow rate, dry-running protection, direction-of-rotation check, standby and low-flow stop (SPE data booklet).

Applications: drinking-water supply boreholes, irrigation, pumping stations on mains or generator power, upgrading a fixed-speed SP pump to variable speed.

Official Grundfos distributor, SINES Export supplies CUE frequency converters, their filters and their accessories to installers, integrators, engineering firms and operators, for worldwide export. Send us the motor nameplate and the cable length: we select the right CUE size and filter. See also the SP submersible pumps, the variable-speed SPE pumps and the CR and CRN pumps.

Grundfos selection: SPE motor, CUE and sine-wave filter

MS6000P motor P2 (kW) Motor current (A) CUE 3 × 380-440 V P2 CUE (kW) I CUE (A) Sine-wave filter Filter current at 100 Hz (A)
4.09.6996167134.0109675497613
5.512.6996167145.5139675497613
7.516.69961671611249675497718
9.221.49961671611249675497826.5
1125.09961671715329675497826.5
1329.29961671715329675501936
1533.49961671818.537.59675501936
18.540.69961671922449675502146.5
2246.29961672030619675503256
2654.09961672030619675503256
3061.89961672137739777443686
3785.699616722459097775142135
45103.0996167235510697775142135

From the “Proposed by Grundfos, easy selection” table in the SPE data booklet: MS6000P motors 3 × 350 V at 3 000 rpm (100 Hz); 200-500 V filters selected on their current at 100 Hz. The motor cable is chosen according to the power: we specify it on the quotation.

When is an output filter required?

Use case (CUE manual) CUE power dU/dt filter Sine-wave filter
SP, BM, BMB pumps with motors of 380 V and aboveall–0 to 300 m
MG71 and MG80 motors up to and including 1.5 kWCUE above 1.5 kW–0 to 300 m
Reduction of dU/dt and noise, low reductionall0 to 150 m–
Reduction of dU/dt, voltage peaks and noise, high reductionall–0 to 300 m
Motors of 500 V and aboveall–0 to 300 m

Common CUE specifications

Specification Value
Functionexternal frequency converter designed for Grundfos pumps, with a start-up guide for each pump family (CR, CRI, CRN, CRT, SP, SP-G, SP-NE…)
Control modesopen loop, constant pressure, constant or proportional differential pressure, constant flow rate, constant temperature, constant level, other constant value
Inputs and outputs1 RS-485 GENIbus port, 1 analogue input 0-10 V / 0-4-20 mA for the external setpoint, 1 analogue input 0-4-20 mA for the sensor, 1 analogue output 0-20 mA, 4 digital inputs (start / stop and 3 programmable), 2 programmable relays
CommunicationGENIbus as standard; other protocols via a CIU communication unit
Motor cablescreened to comply with EN 61800-3; 150 m maximum screened, 300 m unscreened; beyond that, please consult us
InstallationIP20 / IP21 in a cabinet only; IP54 / IP55 never outdoors without protection against water and sun
Altitudeabove 2 000 m, the CUE derates its output: a larger size may be required

Sources: Grundfos CUE manual, Grundfos SPE data booklet and Grundfos 2026 catalogue.

Official Grundfos documents.

The online manual covers CUE units from 0.55 to 90 kW; for sizes of 110 kW and above, we supply the corresponding Grundfos manual with the quotation.

To select the size and the filter, contact us with the motor nameplate, the site voltage and the motor cable length.

References & article codes


Grundfos 2026 catalogue codes. For power ratings not listed and for SP pumps, we determine the size and the filter from the motor nameplate.

CUE frequency converters from the SPE selection table

Article code Designation Power P2 In (A)
99616713CUE 3 × 380-500 V IP20 4 kW4 kW10 / 8.2
99616714CUE 3 × 380-500 V IP20 5.5 kW5.5 kW13 / 11
99616716CUE 3 × 380-500 V IP20 11 kW11 kW24 / 21
99616717CUE 3 × 380-500 V IP20 15 kW15 kW32 / 27
99616718CUE 3 × 380-500 V IP20 18.5 kW18.5 kW37.5 / 34
99616719CUE 3 × 380-500 V IP20 22 kW22 kW44 / 40
99616720CUE 3 × 380-500 V IP20 30 kW30 kW61 / 52
99616721CUE 3 × 380-500 V IP20 37 kW37 kW73 / 65
99616722CUE 3 × 380-500 V IP20 45 kW45 kW90 / 80
99616723CUE 3 × 380-500 V IP20 55 kW55 kW106 / 105

Sine-wave filters from the SPE selection table

Article code Designation Current at 50 Hz (A) Current at 100 Hz (A)
96754976Sine-wave filter 200-500 V IP201713
96754977Sine-wave filter 200-500 V IP202418
96754978Sine-wave filter 200-500 V IP203826.5
96755019Sine-wave filter 200-500 V IP204836
96755021Sine-wave filter 200-500 V IP206246.5
96755032Sine-wave filter 200-500 V IP207556
97774436Sine-wave filter 200-500 V IP2311586
97775142Sine-wave filter 200-500 V IP23180135

Motor temperature monitoring

Article code Designation Function
96760901Module MCB 1141 input 0 / 4-20 mA and 2 Pt100 / Pt1000 inputs

Size your solar pumping system in two minutes

LE LAB, our free online tool, sizes it from your water need, the depth and your location: recommended pump, controller and PV power. No account required.

Launch LE LAB Or request a free study
Project support · Worldwide delivery

Get the support your project needs

From product selection to export logistics, our team helps installers, EPCs and distributors turn a requirement into a clear professional quotation.

B2B supply Sea or air freight Worldwide export
From requirement to delivery
  1. 01Share your products and quantities
  2. 02Receive a clear B2B quotation
  3. 03We coordinate worldwide delivery
Start your request