Solar · Storage · Off-grid B2B worldwide export wholesaler

Professional equipment supply for installers, EPC contractors and distributors.

SINES - Grundfos LiqTec, control unit and sensor

GRUNDFOS LIQTEC



Grundfos sensor and control unit that stop the pump in the event of dry running or excessively hot liquid (130 °C ± 5 °C)

The LiqTec consists of a sensor screwed into the pump via a 1/2 inch thread and an electronic unit on a DIN rail, mounted in a cabinet. Grundfos offers it as an option on CR, CRI and CRN pumps.


Dry running

immediate stop
of the pump

130 °C ± 5 °C

excessively hot liquid
detected

230 V or 115 V

two versions
on DIN rail

Worldwide B2B pump supply and export

Principle: the sensor, screwed into the pump, detects the presence of liquid at the point where dry running must be avoided, for example to protect the mechanical shaft seal. The LiqTec unit monitors this sensor and, through its potential-free run and alarm relays, stops the pump in the event of dry running or excessively hot liquid (130 °C ± 5 °C).

Built-in safety: in the event of a fault in the sensor, its cable, the electronic unit or the power supply, the pump stops immediately. The unit can also monitor the motor temperature via a PTC sensor complying with DIN 44082; without a sensor, the PTC terminals are bridged.

Operation: the front panel groups the indicator lights for dry running, liquid temperature, the PTC sensor and sensor fault, a restart button, a button that disables dry-running monitoring and a manual or automatic reset selector. Reset is manual by default; in automatic mode, the alarm resets 10 to 20 seconds after the liquid returns. The sensor is calibrated in still water, by holding two buttons down for about 20 seconds.

Versions and kits: the complete unit, with sensor and 5 m of cable, is available in 230 V (96556429) and in 115 V (96556430). The MkIII sensor kit (99337830) provides a complete sensor; the extension cable kit (96443676) adds 15 m to reach a maximum of 20 m.

With a Grundfos CUE frequency converter, the “Dry running” function is set on digital input 2, 3 or 4 and accepts a LiqTec sensor, a pressure sensor or a float switch on the suction side. The pump stops and does not restart as long as the input is activated; restart can be delayed by up to 30 minutes depending on the pump family (CUE manual). See also the CUE accessories.

Applications: CR, CRI and CRN pumps in pressure boosting, boiler feed, industrial and process circuits, protection of the mechanical shaft seal against dry running.

Official Grundfos distributor, SINES Export supplies the LiqTec and its kits with the CR, CRI and CRN pumps, the CUE frequency converter and the associated parts, for worldwide export.

LiqTec unit

Specification Value
Power supply230 V AC, 50 / 60 Hz (manual); 115 V version under code 96556430
Power consumption9 VA
Enclosure classIP20: to be installed in a flame-retardant cabinet, in an environment of at least IPX4
MountingDIN rail, in a cabinet; indoors or outdoors depending on the cabinet
Maximum ambient temperature+55 °C
Dimensions66.5 × 90 × 116 mm
Supply fuse8 A maximum

Sensor

Specification Value
Mounting in the pump1/2 inch thread
Maximum pressure40 bar
Maximum liquid temperature+130 °C
Cable5 m as standard, 15 m extension (96443676), 20 m maximum

Inputs and outputs

Specification Value
Run / alarm relay outputpotential-free changeover contact, 250 V, 1 A AC, inductive load
Sensor and PTC inputs11 V DC; PTC sensor to DIN 44082
External restart input5 V CC
Terminals0.5 to 2.5 mm² (AWG 20-13); cables rated for 70 °C minimum

Compliance and maintenance

Specification Value
StandardsIEC 61010-1 (software class A, pollution degree 2, type 1); cURus approval to UL 508
Maintenancenon-repairable product: it is replaced

Sources: Grundfos LiqTec manual, Grundfos 2026 catalogue and Grundfos CUE manual.

Official Grundfos documents.

To equip a pump or a CUE, contact us with the pump model and the available voltage.

References & article codes


Grundfos 2026 catalogue codes. Quotation on request.

Article code Designation Contents
96556429LiqTec complete MkII 230 Vunit, sensor and 5 m of cable
96556430LiqTec complete MkII 115 Vunit, sensor and 5 m of cable
99337830Sensor kit for LiqTec MkIIIcomplete sensor
96443676LiqTec extension cable kit15 m additional, 20 m maximum

Size your solar pumping system in two minutes

LE LAB, our free online tool, sizes it from your water need, the depth and your location: recommended pump, controller and PV power. No account required.

Launch LE LAB Or request a free study
Project support · Worldwide delivery

Get the support your project needs

From product selection to export logistics, our team helps installers, EPCs and distributors turn a requirement into a clear professional quotation.

B2B supply Sea or air freight Worldwide export
From requirement to delivery
  1. 01Share your products and quantities
  2. 02Receive a clear B2B quotation
  3. 03We coordinate worldwide delivery
Start your request